CONCRÈME – the ultimate sealing technology for the protection of engineering concrete

Posted onMarch 17, 2010

CONCRÈME™

CONCRÈME™ is the the ultimate sealing technology for the protection of engineering concrete and masonry from damage caused by water and water bourne salts. CONCRÈME™ is the worlds only low VOC silane which passes California’s new strict VOC guidelines and the new international VOC guidelines. CONCRÈME™ is a permanent bonding alkyl alkoxy silane in an aqueous cream.

TYPICAL APPLICATIONS

CONCRÈME is suitable for a wide variety of applications, including marine infrastructure such as wharves and jetties, road and rail bridge decks, building facades, car parks and swimming pool surrounds. It is an ideal product for the preservation of infrastructure.

.BENEFITS

  • Treated exposed surfaces become easier to maintain and keep looking good for longer.
  • CONCRÈME™ is applied in a single application.
  • Able to repel water and chloride ion (97 per cent reduction); non film-forming; deep penetration – 14 mm into concrete pavers.
  • Able to work without changing the appearance or frictional properties of the surface – keeps the original look; a non-drip gel
  • Ideal for use in windy conditions; is able to breathe so there is no build-up of subsurface moisture – allowing it dry out
  • Very alkali resistant – won’t breakdown in contact with cement-based materials
  • Able to seal hairline cracks up to 0.3 mm (0.012 in.)
  • It is not a surface epoxy, polyurethane or acrylic, so will not flake or peel

Warranty:
A 30-YEAR PERFORMANCE WARRANTY is offered when CONCRÈME is applied by an accredited applicator following our written instructions and tested by us.

Application rates:
One quart per 40 sq.ft. (1 litre per 4 sq.m.) depending on surface absorption.

How to use:
1. ALWAYS TEST PRODUCT ON A SMALL AREA FIRST and allow a 24-hour cure time to determine the ease of application and desired results.
2. Surfaces to be treated must be dry, clean and free of residues, and surface temperature between 40 – 95°F (5 – 35°C).
3. Generously coat the surface with an even layer of CONCRÈME™ using a foam roller, brush or similar.
4. Leave the product to penetrate for minimum of 1 hour, then thoroughly polish off ALL excess product with a clean dry cloth/s. Estimated application rate: 1 Quart per 40 sq.ft. (1 Litre per 4 sq.m.) depending on surface absorption. One coat is usually sufficient but a second coat may be applied at any time once the surface becomes touch dry.
5. Use water to clean equipment.
6. Avoid moisture contact with the surface for a minimum of 12 hours after application.
7. Sealer will NOT prevent surface etching or wear and may darken some surfaces temporarily, returning to the original colour over time. To clean treated surfaces use a neutral pH detergent in warm water and a soft cloth or mop.

Precautions, Safety Directions and Storage:
Do not take internally. Avoid contact with eyes and skin. Avoid inhaling vapours. Wear latex gloves and safety googles during application. No smoking, keep away from naked lights or ignition sources. Keep container tightly sealed in a cool, well ventilated place. Use product before expiry date.

First Aid:
If swallowed, give a glass of water and contact a physician. If skin contact occurs remove contaminated clothing and wash skin thoroughly. If irritation persists, contact a physician. If in eyes, hold open, flood with water for at least 15 minutes and contact a physician. If vapours are inhaled, relocate to fresh air. If symptoms persist contact a physician.

Accidents:
Spillage – Take up mechanically or with absorbent material such as sand, earth or vermiculite. Remove all ignition sources.

Transport:
Not regulated for transport of dangerous goods: DOT (Road), IMDG (Ocean), IATA (Air) Transport

Low VOC’s:
VOC content to US EPA (Method 24) < 100 grams per litre – suitable for use throughout the USA.

Pack size:
2.5 gallon (9.46 Litre) pails

Dry-Treat Dealer. Accredited Applicator.
189 Marua Rd Ellerslie
Auckland Auckland New Zealand
Contact : Dino Gagas Phone 09 526 4581 , Fax 09 526 5909 , Mobile 021-930 066
Aucland
Website : http://www.lustre.co.nz
Email : dino@lustre.co.nz

DRY-TREAT 40N is an impregnating, invisible and breathable sealer

Posted onMarch 17, 2010

DRY-TREAT 40N


DRY-TREAT 40N is an impregnating, invisible and breathable sealer that protects porous tile, natural stone, paving and grout from damage caused by water and salts. Treated indoor and outdoor surfaces become easier to clean, maintain and keep looking good for longer. DRY-TREAT 40N provides lasting protection for engineering concrete, render, terracotta tile, cast stone, paving, limestone, brick and grout.

Typical applications: DRY-TREAT 40N is suitable for a wide variety of applications, including building facades, floors, walls, swimming pool surrounds, patios, garages, kitchens and public and private entertaining areas.

Benefits: DRY-TREAT 40N non film-forming; able to work without changing the appearance of the surface – keeps the original look; suitable for indoor and outdoor use; able to greatly reduce water uptake and minimise moss growth, freeze thaw spalling and efflorescence; an excellent chloride ion salt screen – ideal for marine and pool areas; highly water vapour permeable – able to breathe so there is no build-up of subsurface moisture, allowing it dry out; deeply penetrating – protecting against weathering and wearing; very alkali resistant – won’t breakdown in contact with cement based materials; and able to seal hairline cracks up to 0.3 mm (0.012 in.) and does not flake or peel, and able to stop rising damp.

Warranty: A 15-YEAR PERFORMANCE WARRANTY is offered when DRY-TREAT 40N is applied by an accredited applicator following our written instructions.

Application rate: Total application rate is approximately one litre per one to four sq. metres (10 to 40 sq. feet per quart) depending on absorption.

How to use:
1. ALWAYS TEST PRODUCT ON A SMALL AREA FIRST and allow a 24 hour cure time to determine the ease of application and desired results.
2. Ensure surfaces to be treated are dry, clean and free of residues.
3. Product is to be applied without thinning.
4. Generously saturate the surface with product using a low-pressure hand spray, a clean brush, or similar. Surface should have a mirror-like “wet” look for 3-5 seconds. Avoid contact with surrounding areas. 5. After 10 minutes, repeat Step 4. Total application rate is approximately one litre per one to four sq. metres (10 to 40 sq. feet per quart) depending on absorption.
6. Allow 10 minutes for product to penetrate surface then polish surface with a clean white dry cloth to remove excess product.
7. Clean equipment with organic solvent.
8. Sealer will not prevent surface etching or wear and may lighten or darken some surfaces.

Precautions: Do not take internally. Apply when surface temperature is between 5 – 35 ºC (40 – 95 ºF). Avoid moisture contact with the surface for six hours after application. Protect surrounding areas from over-spray. Keep away from drains, plants, water and soil. Use only in well-ventilated areas. Use a positive pressure respirator if ventilation is inadequate. Wear suitable solvent-resistant gloves, protective clothing, safety goggles and an organic vapour respirator during application. Avoid applying in windy conditions. Wash hands thoroughly.

Active content: A mixture of 40 per cent active content in alcohol.

Pack size: 20 litre pails.

Dry-Treat Dealer. Accredited Applicator.
189 Marua Rd Ellerslie
Auckland Auckland New Zealand
Contact : Dino Gagas Phone 09 526 4581 , Fax 09 526 5909 , Mobile 021-930 066
Aucland
Website : http://www.lustre.co.nz
http://www.drytreat.com
Email :dino@lustre.co.nz

WATER-REPELLA is a penetrating, invisible and breathable sealer

Posted onMarch 17, 2010

WATER-REPELLA

WATER-REPELLA is a penetrating, invisible and breathable sealer that protects porous tile, natural stone, paving and grout from damage caused by water and salts. Treated indoor and outdoor surfaces become easier to clean, maintain and keep looking good for longer. WATER-REPELLA is an economical sealer for engineering concrete, terracotta tile, cast stone, paving, limestone, brick and grout.

TYPICAL APPLICATIONS
WATER-REPELLA is suitable for a wide variety of applications, including building facades, floors, walls, swimming pool surrounds, patios, garages, kitchens and public and private entertaining areas.

BENEFITS
WATER-REPELLA able to greatly reduce water uptake and minimise moss growth, freeze thaw spalling and efflorescence; non film-forming; able to work without changing the appearance of the surface – keeps the original look; suitable for indoor and outdoor use; able to breathe so there is no build-up of subsurface moisture, allowing it dry out, and very alkali resistant – won’t breakdown in contact with cement-based materials.

Application rates
Total application rate is approximately one litre per two to eight sq. metres (20 to 80 sq. feet per quart) depending on absorption.

How to use
1 ALWAYS TEST PRODUCT ON A SMALL AREA FIRST and allow a 24 hour cure time to determine the ease of application and desired results.
2 Ensure surfaces to be treated are dry, clean and free of residues.
3 Product is to be applied without thinning.
4 Generously saturate the surface with product using a low-pressure hand spray, a clean brush, or similar. Surface should have a mirror-like “wet” look for 3-5 seconds. Avoid contact with surrounding areas.
5 After 10 minutes, repeat Step 4. Total application rate is approximately one litre per two to eight sq. metres (20 to 80 sq. feet per quart) depending on absorption.
6 Allow 10 minutes for product to penetrate surface then polish surface with a clean white dry cloth to remove excess product.
7 Clean equipment with water.
8 Sealer will not prevent surface etching or wear and may lighten or darken some surfaces.

Precautions
Do not take internally. Apply when surface temperature is between 5 – 35 ºC (40 – 95 ºF). Avoid moisture contact with the surface for six hours after application. Protect surrounding areas from over-spray. Keep away from drains, plants, water and soil. Use only in well-ventilated areas. Use a positive pressure respirator if ventilation is inadequate. Wear suitable solvent-resistant gloves, protective clothing, safety goggles and an organic vapour respirator during application. Avoid applying in windy conditions. Wash hands thoroughly.

Active content
Less than 10 per cent active content in water.

Pack size
5 & 20 litre (1.3 US gallon, 5.3 US gallon) plastic drums.

Storage
Use product within 12 months of purchase. Keep container tightly sealed, in a cool well-ventilated place. Product is freeze-thaw stable.

Dry-Treat Dealer. Accredited Applicator.
189 Marua Rd Ellerslie
Auckland Auckland New Zealand
Contact : Dino Gagas Phone 09 526 4581 , Fax 09 526 5909 , Mobile 021-930 066
Aucland
Website : http://www.lustre.co.nz
http://www.drytreat.com
Email :dino@lustre.co.nz