WATER-REPELLA is a penetrating, invisible and breathable sealer

Posted onMarch 17, 2010

WATER-REPELLA

WATER-REPELLA is a penetrating, invisible and breathable sealer that protects porous tile, natural stone, paving and grout from damage caused by water and salts. Treated indoor and outdoor surfaces become easier to clean, maintain and keep looking good for longer. WATER-REPELLA is an economical sealer for engineering concrete, terracotta tile, cast stone, paving, limestone, brick and grout.

TYPICAL APPLICATIONS
WATER-REPELLA is suitable for a wide variety of applications, including building facades, floors, walls, swimming pool surrounds, patios, garages, kitchens and public and private entertaining areas.

BENEFITS
WATER-REPELLA able to greatly reduce water uptake and minimise moss growth, freeze thaw spalling and efflorescence; non film-forming; able to work without changing the appearance of the surface – keeps the original look; suitable for indoor and outdoor use; able to breathe so there is no build-up of subsurface moisture, allowing it dry out, and very alkali resistant – won’t breakdown in contact with cement-based materials.

Application rates
Total application rate is approximately one litre per two to eight sq. metres (20 to 80 sq. feet per quart) depending on absorption.

How to use
1 ALWAYS TEST PRODUCT ON A SMALL AREA FIRST and allow a 24 hour cure time to determine the ease of application and desired results.
2 Ensure surfaces to be treated are dry, clean and free of residues.
3 Product is to be applied without thinning.
4 Generously saturate the surface with product using a low-pressure hand spray, a clean brush, or similar. Surface should have a mirror-like “wet” look for 3-5 seconds. Avoid contact with surrounding areas.
5 After 10 minutes, repeat Step 4. Total application rate is approximately one litre per two to eight sq. metres (20 to 80 sq. feet per quart) depending on absorption.
6 Allow 10 minutes for product to penetrate surface then polish surface with a clean white dry cloth to remove excess product.
7 Clean equipment with water.
8 Sealer will not prevent surface etching or wear and may lighten or darken some surfaces.

Precautions
Do not take internally. Apply when surface temperature is between 5 – 35 ºC (40 – 95 ºF). Avoid moisture contact with the surface for six hours after application. Protect surrounding areas from over-spray. Keep away from drains, plants, water and soil. Use only in well-ventilated areas. Use a positive pressure respirator if ventilation is inadequate. Wear suitable solvent-resistant gloves, protective clothing, safety goggles and an organic vapour respirator during application. Avoid applying in windy conditions. Wash hands thoroughly.

Active content
Less than 10 per cent active content in water.

Pack size
5 & 20 litre (1.3 US gallon, 5.3 US gallon) plastic drums.

Storage
Use product within 12 months of purchase. Keep container tightly sealed, in a cool well-ventilated place. Product is freeze-thaw stable.

Dry-Treat Dealer. Accredited Applicator.
189 Marua Rd Ellerslie
Auckland Auckland New Zealand
Contact : Dino Gagas Phone 09 526 4581 , Fax 09 526 5909 , Mobile 021-930 066
Aucland
Website : http://www.lustre.co.nz
http://www.drytreat.com
Email :dino@lustre.co.nz

“Bio-Clean” Water Stain Remover

Posted onFebruary 24, 2010

Bio-Clean” Water Stain Remover

Bio-Clean is a professional strength cleaner recommended by both glazing contractors and professional window cleaning companies. It is successfully used in hospitals, nursing homes, manufacturing plants, hotels, supermarkets and other public facilities with difficult to clean surfaces.

1234

Benefits of this Product




bullet Effectively Removes Water and Mineral Stains, Rust, Soap Scum and Mildew from Glass and Other Surfaces
bullet Works Great On: Shower Door Works Great On: Shower Door “GLASS ONLY”, Windows, Glass Surfaces, Tile and Fiberglass, Windshields, Chrome, Porcelain, Corian, Stainless Steel and Hard Vinyl
bullet Removes Stage 1 Corrosion Quickly…  *SEE IMPORTANT NOTE BELOW*

Apply Bio-Clean to a surface with a dry cloth, sponge, brush or oscillating buffer. Press firmly to loosen stain with a rubbing action, then just rinse with water until residue free. Can be reapplied as needed until surface is clean. Stage 1 Corrosion is defined as glass with light corrosion, with little or no damage to the glass. Stage II Corrosion occurs when the deposits are no longer on the surface of the glass, but have started to break down the molecular structure of the glass, leaving an etched or white haze on the glass after the stain has been removed.  Bio-Clean Water Stain Remover will not repair glass with Stage II Corrosion. (we are not responsible or liable if your stains/spots are at Stage II, therefore, we cannot accept returns on this item).  DO NOT APPLY TO THE HARDWARE OF YOUR SHOWER DOOR.  FOR GLASS ONLY.

Source:  http://www.cleanshowerdoor.com/Bio.htm