PRISM® SureColor Grout -Technical Data Sheet

Posted onDecember 20, 2010

PRISM® SureColor® Grout -Technical Data Sheet


* 32% lighter than other groutstl
* A 7.71kg bag covers the same area as an 11.34kg bag
* Formulated with CustomLite™ Technology
* Exclusive SureColor® Promise
* Consistent colour with no shading
* No efflorescence
* Stain resistance
* Cures quickly and develops high early strength
* No shrinkage for joints 1.6mm to 13mm wide
* Contributes to LEED Certification
* Protected by MoldGard® Technology to resist mould and mildew growth
* Covered by a Commercial Warranty

Tile Types:
Vitreous, semi-vitreous or absorptive tile: ceramic, mosaic, quarry, pavers, cement, porcelain, brick, mini-brick, precast terrazzo and natural stone

Bag Size: 7.71kg

Prism® SureColor® Brochure PDF

Technical Data Sheet PDF

Data Sheet PDF

Material Safety Data Sheet PDF

Global Tile Ltd
81 Mays Road, Onehunga
Auckland,1061, New Zealand
http://www.globaltile.co.nz
PO Box 12-504, Penrose
Auckland 1642, New Zealand

P: +64-9-6340712
F: +64-9-6342736

Rapidfix-FAST SETTING,TWO PACK, ADHESIVE- CONSTRUCTION CHEMICALS

Posted onJanuary 24, 2010

Rapidfix-FAST SETTING,TWO PACK, ADHESIVE-
CONSTRUCTION CHEMICALS
.

DESCRIPTION
A two component rapid drying cement based adhesive for stone and stone composites that are affected by
moisture and require a rapid drying adhesive.
USES
For bonding ceramic tiles, terrazzo tiles, reconstituted stone, natural stone, granite and marble to floors and walls,
externally and internally where fast drying and set times are required combined with high strength and flexibility.
FEATURES
• High early strength.
• Tiled surfaces can be grouted after 3 hours and are completely cured after 24 hours for normal use –
(3 days cure time for immersed application).
• Low shrinkage.
• High bond strength.
• Resistant to impact, vibration, temperature, ageing and dilute chemicals.
COVERAGE (approximate)
4m2 per 20kg/5lt pack using 10 x 10mm notched trowel.
PERFORMANCE DATA
28 day tensile strength 2.8Mpa
28 day flexural strength 5Mpa
28 day compression strength 20Mpa
Temperature Resistance -20°C to +81°C
SPECIFICATION
The two part rapid setting and drying adhesive must have a 28 day tensile strength of 2.8Mpa and compression
strength of 20Mpa and be capable of being grouted in three hours and put into normal use in 24 hours such as
RAPIDFIX manufactured by Construction Chemicals and shall be applied in accordance with the manufacturer’s
instructions.
SURFACE PREPARATION
Surfaces to be tiled must be structurally sound, clean and free from waxes, coatings, oil, grease, laitance and all
contaminants. Concrete must be cured 28 days and render 7 days prior to being tiled.
Prime the substrate with PRIMAX. Dampen down surfaces that have been heated by the sun to cool them
down. If this is not possible, apply the adhesive in the shade.
MIXING
Mix using a slow speed power mixer. Pour 5lt of liquid into the mixing container and slowly add powder until a
lump free paste mixture is obtained (always add powder to liquid). Clean mixing container out between mixes
to avoid shortening pot life.
Mix Ratio
Grey 20kg powder to 5lt liquid
White 20kg powder to 5lt liquid
Pot life is 45 minutes at 23°C @ 50% relative humidity. Higher temperatures will reduce this time.

APPLICATION
Apply the adhesive to the primed surface with a notched trowel, 6 x 6mm for walls and 10mm x 10mm for floors.
Butter large or irregular backed tiles with 3-5mm thick even bed.The final adhesive bed must be not less than 2mm for
walls and 3mm for floors. Spread a metre at a time and check it does not skin on the surface.The open time is 15-20
minutes In normal conditions (shaded areas at 23°C at 50% relative humidity).Application in sun, strong dry winds and
or high temperature can reduce this to a few minutes.The substrate can be dampened prior to applying the adhesive
but do not wet down the surface of the adhesive. Respread the adhesive, with notched trowel, if skinning occurs.
Tiles must be set in place while the adhesive is still wet on the surface. Press tiles firmly into the adhesive using a slight
twisting motion.Tiles must be bedded into the adhesive so no voids occur beneath the tiles.Adjustment can be made
up to 10-15 minutes after fixing.
Protect the tiles surface from rain and water for 3-4 hours and from strong sun for 12 hours.
GROUTING
Grouting can be commenced after 3 hours. Grout with KEMGROUT mixed with PRIMER & GROUT ADDITIVE or
EPEGROUT.
SET TIME
Light traffic after 3-4 hours
Polishing after 24 hours
Heavy traffic after 24 hours
Immersed application – 72 hours
CLEANING
Before the adhesive has set, with water.
PRECAUTIONS
• Do not use on surfaces subject to rising damp.
• Do not use on metal or flexing building boards eg. Cement sheet, wood panels.
• Do not use on green marble or stone containing metal pigments which are subject to moisture expansion.

Full  Technical Data Sheet at:http://www.constructionchemicals.com.au/

Sydney
2/31-33 Newton Rd, Wetherill Park
New South Wales
Ph: (02) 9756 3533  Fax: (02) 9756 3534