POLYBLEND® White Dry Grout -Technical Data Sheet

Posted onDecember 20, 2010

POLYBLEND® White Dry Grout -Technical Data Sheet

* Polymer modified Non-Sandedtl
* Mix with water
* For any tile or stone installation
* Resistant to shrinking, cracking, powdering and wear
* Suitable for joints up to 3mm wide
* For highly glazed ceramic tile or highly polished natural stone
* For interior and exterior installations
* Rated for residential to extra heavy duty commercial use
* Protected by MoldGard® Technology to resist mould and mildew growth
* Covered by a Commercial Warranty and a Homeowner Warranty

Tile Types:
Vitreous, semi-vitreous or absorptive tile: ceramic, mosaic, quarry, cement, impervious porcelain and glass tile, brick and mini-brick, precast terrazzo and natural stone tile

Bag Size: 11.34kg
Colour: White

Technical Data Sheet PDF

Data Sheet PDF

Global Tile Ltd
81 Mays Road, Onehunga
Auckland,1061, New Zealand
http://www.globaltile.co.nz
PO Box 12-504, Penrose
Auckland 1642, New Zealand

P: +64-9-6340712
F: +64-9-6342736

PCI Tilefast 6 Rapidflex -fast-setting, polymer-modified, high-performance tile adhesive -TDS, MSDS.

Posted onMarch 17, 2010

PCI Tilefast 6 Rapidflex -fast-setting, polymer-modified, high-performance tile adhesive –TDS, MSDS.

This fast-setting, polymer-modified, high-performance tile cement is walkable after just three hours*. It’s a true fast-track product allowing early tiling to bonded screeds and is suitable for use in continuously-immersed situations. It is perfect for applications which may experience some shrinkage, vibration, flexing or heavy loads and traffic and as a cost effective alternative to expensive latex it provides excellent adhesion to a variety of substrates. Can be used on underfloor heating floors.

Features & Benefits
Flexible and fast-setting – walkable after 3 hours
Just mix with water
For fully-vitrified and tile-on-tile work
Water and frost resistant
Flexible bed minimises tile cracking
Exceeds BS EN 12004 Class C2FT
Available sizes: 10kg, 20kg

Packaging
10kg & 20kg Paper Sack

GREY MSDS

TDS

WHITE MSDS

BASF Construction Chemicals (UK) Ltd,
PO Box 4, Earl Road, Cheadle Hulme, Cheadle, Cheshire, SK8 6QG,
Tel. 0161 485 6222,
Fax 0161 488 5220.

http://www.pci.uk.com

Flexi Flex-polymer modified adhesive for bonding all types of tiles-Technical Data Sheet.

Posted onMarch 17, 2010

Flexi Flex-polymer modified adhesive for bonding all types of tiles-Technical Data Sheet.

* Cost Effective
* Rubber Based
* High Bond Strength
* Flexural Strength
Description

Flexi Flex is an off white adhesive composed of cement, fine graded sands and other special additives. This adhesive has been polymer modified for bonding all types of tiles to a variety of substrates subject to vibration and thermal movement and to achieve a high bond strength with non-porous tiles.
Precautions

Flexi Flex is unsuitable for:

*
bonding moisture sensitive green marble;
*
bonding to MDF board or timber & wax impregnated wood;
*
bonding to substrates subject to constant water immersion such as swimming pools.

SUBSTRATE PREPARATION & EXPANSION JOINTS

All substrates to be tiled must be flat and true, free from oil, dirt, grease or any other contaminants. Very porous substrates should be primed with Plastinex (1 part Plastinex mixed with 4 parts water). Incorporate expansion joints in accordance with AS 3958.1 2007.
Concrete: New concrete must be allowed to cure for 6 weeks and should have a wood float finish. Use Floor Prep to acid etch an adhesive key into concrete finished with a steel float. Cement Render: Render to be left with a wood float finish and allowed to cure for 7 days. Fibre Cement Sheets: Fibre cement sheets must be primed with Plastinex (1 part Plastinex mixed with 4 parts water) and all joints must be taped with PVC duct tape and fixed according to the manufacturer’s instructions. Plasterboard: Plasterboard must be fixed as per manufacturer’s instructions. Jointing compound must be primed with Plastinex (1 part Plastinex mixed with 4 parts water).
MIXING & POT LIFE

Add Flexi Flex to clean water at a ratio of 25kg to 6 litres of water. Mix the adhesive to a smooth paste free from lumps by using a drill that has a speed lower than 300 rpm, or mix by hand. Slacken the adhesive and re-mix after 5 minutes. Flexi Flex has a pot life of approximately 3 hours at 23°C and 50% relative humidity.
OPEN TIME

Flexi Flex has an open time of approximately 30 minutes, which can be shortened to just a few minutes by the action of sun, wind, high temperatures or highly absorbent surfaces. Dampening or priming the substrate prior to tiling prolongs the open time of the adhesive. Tilers need to constantly check that the adhesive has not formed a surface skin and is still fresh to touch. Adhesive with a surface skin must be always removed and discarded.
APPLICATION, TOOLS AND ADJUSTABILITY TIME

Always install the tiles in accordance with AS 3958 1:1991 and ensure the backs of the tiles are free of dust. Spread Flexi Flex evenly across one square metre at a time with a 6mm notched trowel for walls and a 10mm notched trowel for floors. The choice of trowel should be governed by the depth of the knobs, grooves or ridges on the back of each tile and the evenness of the substrate. Lay the tiles with a fair pressure and at right angles to the adhesive notched pattern. The final bed of adhesive should be between 2mm and 4mm. Wall tiles should have a finished joint width of 2mm – 4mm and floor tiles should have a finished joint width of 3mm – 6mm. Tiles can be adjusted for approximately 10 minutes after laying.
COVERAGE

25kgs of Flexi Flex will cover approximately 12 square metres with a 6mm notched trowel for walls and approximately 10 square metres with a 10mm notched trowel for floors.
CURE TIME

Flexi Flex cures in approximately 24 hours at 23°C and 50% relative humidity. High density substrates or tiles and temperatures during installation below 10°C will significantly increase the cure time.
CLEAN UP

Remove excess Flexi Flex from the grout joints after 30 minutes and clean the tiles with a damp cloth or sponge. Tools and hands can be cleaned with water while the adhesive is still wet.
JOINT GROUTING

Depending on environmental conditions, commence grouting after approximately 12 hours. Use Regular or Superior Grout for grout joints between 3mm to 6mm. Morgan Slate & Quarry Grout should be used for joint sizes between 6mm to 20mm. Use Aquapoxy, a three component anti-acid epoxy grout, if the joints are required to have a good chemical resistance. Grout Add may also be mixed with Regular Grout to impart extra flexibility, reduce porosity and increase water resistance.
JOINT GROUTING PRECAUTIONS

DO NOT use excessive amounts of water during mixing or initial cleaning as this will cause irregular colour finishes and also weaken the grout. DO NOT mix the grout with an electric drill above 300 RPM as this can entrap air into the mix causing grout to dry soft and powdery or with unsightly pin holes in the surface. All grouts should be Damp Cured for 48 hours. Refer to the Australian Standard AS 3958 Part 1 Section 5.7.3.
SHELF LIFE

Twelve months if stored in a dry & elevated position in the original factory sealed packaging.
Packaging

Flexi Flex is available in 25kg bags.
SPECIFICATION CLAUSE

The wall & floor adhesive shall be Morgan Flexi Flex – a tile adhesive complying with all relevant Australian technical standards.
MORGAN QUALITY POLICY STATEMENT

Flexi Flex is manufactured and distributed to a quality system based on ISO 9001:2000. Flexi Flex is guaranteed for 10 years when installed to the guidelines of AS 3958 Part 1 & 2 and in conjunction with written technical information supplied by Morgan Ceramic Tile Adhesives.

Guarantee

Morgan Ceramic Tile Adhesives

http://www.morganadhesives.com.au
11 Raymond Avenue
Bayswater 6053
Western Australia

Telephone +61 8 9272 4666
Facsimile +61 8 9370 1744

accounts@morganadhesives.com.au
info@morganadhesives.com.au